\r序<\/span>  <\/span>號<\/span><\/span> \r<\/p>\r<\/td>\r

\r項<\/span>  <\/span>目<\/span><\/span> \r<\/p>\r<\/td>\r

\r規<\/span> 格<\/span> 參<\/span> 數<\/span><\/span> \r<\/p>\r<\/td>\r

\r數量或要求<\/span><\/span> \r<\/p>\r<\/td>\r

\r備<\/span>  <\/span>注<\/span><\/span> \r<\/p>\r<\/td>\r<\/tr>\r

\r3.3.1<\/span> \r<\/p>\r<\/td>\r

\r工藝流程<\/span><\/span> \r<\/p>\r<\/td>\r

\r首先<\/span><\/i><\/b>，手動將<\/span>TP<\/span>撕掉保護膜反放在左邊平臺上；其次<\/i><\/b>，手動將液晶模組放到右邊治具上，按真空吸住，撕掉保護膜；再次<\/i><\/b>，雙手按啟動按鈕，左邊平臺后移至上治具下方，真空腔體和上治具在伺服電機帶動下下移把<\/span>TP<\/span>自動夾起，然后移動到<\/span>CCD1<\/span>上方找位置，同時下治具在伺服電機的作用下移動到<\/span>CCD2<\/span>和<\/span>CCD3<\/span>的下方對位，<\/span>DD<\/span>馬達帶動上治具旋轉對位，對位完畢上下治具移動到同一位置，真空腔體下移密封抽真空，當真空值達到<\/span>-100Kpa<\/span>開始貼合，貼合完成，上下治具復位人工取走貼完產品，單次循環結束。<\/span><\/span> \r<\/p>\r

\r <\/span> \r<\/p>\r<\/td>\r

\r <\/span> \r<\/p>\r<\/td>\r

\r <\/span> \r<\/p>\r<\/td>\r<\/tr>\r

\r3.3.2<\/span> \r<\/p>\r<\/td>\r

\r功能<\/span><\/span> \r<\/p>\r<\/td>\r

\r所有參數（如：壓合時間）能通過工控機設定，并在顯示器上顯示<\/span><\/span> \r<\/p>\r<\/td>\r

\r <\/span> \r<\/p>\r<\/td>\r

\r <\/span> \r<\/p>\r<\/td>\r<\/tr>\r

\r3.3.3<\/span> \r<\/p>\r<\/td>\r

\r貼合精度<\/span>mm<\/span> \r<\/p>\r<\/td>\r

\r<<\/span>±<\/span>0.1mm<\/span> \r<\/p>\r<\/td>\r

\r <\/span> \r<\/p>\r<\/td>\r

\r <\/span> \r<\/p>\r<\/td>\r<\/tr>\r

\r3.3.4<\/span> \r<\/p>\r<\/td>\r

\r上下料<\/span><\/span> \r<\/p>\r<\/td>\r

\r1<\/span>）兩人在左右治具上下料<\/span><\/span> \r<\/p>\r<\/td>\r

\r <\/span> \r<\/p>\r<\/td>\r

\r <\/span> \r<\/p>\r<\/td>\r<\/tr>\r

\r3.3.5<\/span> \r<\/p>\r<\/td>\r

\r產品換型<\/span><\/span> \r<\/p>\r<\/td>\r

\r1）  <\/span><\/span>專用用模板，用防靜電防刮傷材料制造<\/span><\/span> \r<\/p>\r

\r2）  <\/span><\/span>更換新產品時，調校時間約<\/span>30min<\/span> \r<\/p>\r

\r3）  <\/span><\/span>更換產品時，調校時間約<\/span>20min<\/span> \r<\/p>\r<\/td>\r

\r <\/span> \r<\/p>\r<\/td>\r

\r <\/span> \r<\/p>\r<\/td>\r<\/tr>\r<\/tbody>\r<\/table>\r

\r 
\r<\/span> \r<\/p><\/div>