一区二区吉沢明步免费视频 ,丰满少妇被猛烈进入试看,亚洲永久在线,国产aⅴ麻豆系列尤物,TUBE44VIDEOS欧美,伊人av一区二区无码,又长又大又粗又硬3p免费视频,东京热制服丝袜无码专区,中文字幕无码av专区久久,狠狠色丁香婷婷综合尤物

\r序<\/span> 號<\/span> \r<\/p>\r<\/td>\r

\r項<\/span> 目<\/span> \r<\/p>\r<\/td>\r

\r規<\/span>格<\/span>參<\/span>數<\/span> \r<\/p>\r<\/td>\r

\r數量或要求<\/span> \r<\/p>\r<\/td>\r

\r備<\/span> 注<\/span> \r<\/p>\r<\/td>\r<\/tr>\r

\r4.3.1\r<\/p>\r<\/td>\r

\r工藝流程<\/span> \r<\/p>\r<\/td>\r

\r首先<\/span><\/i><\/b>，手動將<\/span>TP撕掉保護膜反放在中間平臺上；其次<\/i><\/b>，手動將液晶模組放到右邊治具上，按真空吸住，撕掉保護膜；再次<\/i><\/b>，雙手按啟動按鈕，中間平臺后移至上治具下方，真空腔體和上治具在伺服電機帶動下下移把<\/span>TP自動夾起，然后移動到<\/span>CCD1上方找位置，同時下治具在伺服電機的作用下移動到<\/span>CCD2和<\/span>CCD3的下方對位，<\/span>DD馬達帶動上治具旋轉對位，對位完畢上下治具移動到同一位置，真空腔體下移密封抽真空，當真空值達到<\/span>-100Kpa開始貼合，貼合完成，上下治具復位人工取走貼完產品，單次循環結束。<\/span> \r<\/p>\r

\r
\r<\/p>\r<\/td>\r

\r
\r<\/p>\r<\/td>\r

\r
\r<\/p>\r<\/td>\r<\/tr>\r

\r4.3.2\r<\/p>\r<\/td>\r

\r功能<\/span> \r<\/p>\r<\/td>\r

\r所有參數（如：壓合時間）能通過工控機設定，并在顯示器上顯示<\/span> \r<\/p>\r<\/td>\r

\r
\r<\/p>\r<\/td>\r

\r
\r<\/p>\r<\/td>\r<\/tr>\r

\r4.3.3\r<\/p>\r<\/td>\r

\r貼合精度<\/span>mm\r<\/p>\r<\/td>\r

\r<±<\/span>0.1mm\r<\/p>\r<\/td>\r

\r
\r<\/p>\r<\/td>\r

\r
\r<\/p>\r<\/td>\r<\/tr>\r

\r4.3.4\r<\/p>\r<\/td>\r

\r上下料<\/span> \r<\/p>\r<\/td>\r

\r1）兩人在左右治具上下料<\/span> \r<\/p>\r<\/td>\r

\r
\r<\/p>\r<\/td>\r

\r
\r<\/p>\r<\/td>\r<\/tr>\r

\r4.3.5\r<\/p>\r<\/td>\r

\r產品換型<\/span> \r<\/p>\r<\/td>\r

\r1） <\/span>專用用模板，用防靜電防刮傷材料制造<\/span> \r<\/p>\r

\r2） <\/span>更換新產品時，調校時間約<\/span>30min\r<\/p>\r

\r3） <\/span>更換產品時，調校時間約<\/span>20min\r<\/p>\r<\/td>\r

\r
\r<\/p>\r<\/td>\r

\r
\r<\/p>\r<\/td>\r<\/tr>\r<\/tbody>\r<\/table>\r

\r
\r<\/p>\r

\r
\r<\/p>\r<\/div>